Then click on the Day & Night dropdown and change it to "Color."ĥ) Click "Save" at the bottom of the page. You should notice the image to the left has changed to black and white, once it does click save.Ĥ) Click on the profile drop-down at the top again and select Day this time. If your plugins are installed you will see a window with the cameras feed in it to the left and a set of controls to the right.Ģ) Click on the drop-down tab that says "Normal" and select Night.ģ) On the right-hand side select the drop-down box for Day & Night and choose Black and White. ![]() Since we've now added the camera to the network, defaulted the camera, set the date and time, and have given it a schedule lets take the last step and configure the profile for day and night.ġ) Click on the Conditions tab at the left side of the page. How to Configure the Day and Night Profile Let's move on to configuring the profile for Day and Night. You now have your time block configured for Daylight. Try going back to conditions and clicking default before moving ahead.Ĥ) Your window should change to something similar to the image below.īy default, the schedule will populate the day profile across 24 hours.ĥ) Click and hold on the end tab and drag it into the time your sunrise occurs.Ħ) Click and hold on the other end tab and drag it into the time your sunset occurs. If it's not that might be the cause of errors. Then click Conditions.Ģ) Click on the Profile Management tab in the middle of the page.ģ) Your profile should be set to Normal. Setting the schedule.ġ) Click on the Camera drop-down on the left side. How to Configure A Day/Night Schedule Manuallyįinally, what we've set out to accomplish. Just check the box, select your NTP server, make sure the camera has access to the Internet. It is recommended that you do so as over time the camera starts to lose time. Optionally you may sync with an NTP Server. Click Sync PC - this will sync it's date and time to the current settings.Set Daylight Savings Time - Click on DST Enable - then click the Week radio button - follow the second picture below for the days and times that daylight savings starts and ends.Set your time zone - Eastern is GMT -05:00.The camera will be looking to its internal clock to keep its schedule.ġ) Click on the System drop-down on the left side of the screen.Ģ) Click General under the system drop-down menu.ģ) Click on the Date&Time tab in the middle of the screen.Ĥ) Now we've landed in the settings for "Date & Time." Configure the time in the following order: If your time isn't set right, then setting a schedule would be pointless. Configuring Date and Time On Your IP Camera Follow the guides below to configure the camera. You've now landed in the settings portion of your IP camera's web server. If you're prompted to install plugins please follow the link posted above in step 2 for Enabling ActiveX to View Your IP Cameras and DVR Over the Web.Ģ) Click on the "Setting" or "Setup" tab in the top right corner of the screen. Configure day settings and night settingsġ)Open IE11 and enter the address of your camera into the URL bar at the top of the page.Make sure that the time is set on your camera.Default the camera if any settings are already incorrect.There are a few points to cover for this configuration: Step 3: Configuring the Camera for Scheduled Day/Night Mode If you have your IP camera connected to your NVR directly you can also access the camera's web interface through your NVR without any complicated networking.īefore moving on to on Step 3 make sure your computer is connected to the same network as the IP camera. You can follow this guide here: Enabling ActiveX to View Your IP Cameras and DVR Over the Web There are a few steps that you'll have to take with the browser in order have the ActiveX controls fully functional. ![]() ![]() Using Google Chrome, Microsoft Edge, Mozilla Firefox or Safari will not give you access to the camera. When using the IP camera's built-in web server to access the settings you must use a browser that is compatible with ActiveX. ![]() Step 2: Accessing Your IP Camera from the Web If you don't have a PoE switch then you will need to power the camera using one of the following: In order to log into the camera, it must be connected to your local network using a PoE switch. If you already know how to pull up the camera's web interface, then skip to Step 3. Step 1: Connect the Camera to Your Network
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |